Electrician Hand Tools

Screw Driver - 

They are used to tighten and unscrew different types of screws. There are several types; Such as flat tip, cross tip, u tip etc. Their size is judged by the length of their shank or blade. Their main parts are tip, shank or blade and handle.

Combination Plier - 

It is used for cutting thin wires of aluminum and copper, peeling their insulation and twisting wire joints. It usually goes 15 to 20 cm in length.

Nose plier - 

It is used to hold thin wires, squeeze and tighten small sized nuts. It means 15 cm long, long with insulated handle, and flat noose with flat beak, round nose, banner nose, long nozzle type.

Nipper- 

It is also called 'side cutting plier or 'diagonal cutter'. It is used to cut thin corners of copper and aluminum.

Wire Stripper - 

This tool is used to peel insulation of wires in electrical wiring. Its length is usually 20 cm.

Phase Tester - 

Its head has a carbon resistor and a neon lamp connected between the shank and the metallic cap above the head. It is used to check the presence of 'phase'. It is designed to work up to 500 volts.

Electrician knife- 

This is two blading knife. It has a blade edge which is used to peel the insulation of the wires.

Hammer- 

It is used for hammering nails, ballast and raval plugs, punching walls with cheese, etc. and working with firmer cheese on wood. Its main parts are - face, pean, eye hole, cheek and handle. There are several types of hammers; Such as ball-pean, cross pean, straight pean, riveting, sled, soft etc.

Center punch - 

This is used to mark before punching in metallic sheets so that the drill bits move only while staying on the guide hole. It is made of steel and its length is usually 10-15 mm.

Poker - 

This is used to make a small guide hole for the screw before tightening the screw in the wooden fitting. It is also called 'Sumbi' or Bradle. Its tip is pointed and it gets square at the back.

Rawal plug tool - 

it is used to make holes in walls, ceilings etc. By punching in the wall, roof etc., they rotate bit by bit. Its bits are made of tool-steel and can be tightened and opened in the handpiece as required.

Test lamp - 

This tool is made by tightening two pieces of 1 mm2 size pvc wire about half-a-meter long and fitted to a 60 watt lamp in a backlight holder. By this, the phase, neutral and earth wires of the AC supply line are identified and defects are discovered on the basis of its burning, non-burning or less burning.

Chiesel - 

It is used for shaping various types of wood and mica sheets and fittings as required. They are mainly of two types - cold and hot. Blacksmiths have used hot cheese. Cold cheeses are commonly cross-cut, flat, round nose, diamond nose, cow mouth side-cutting type phenomenon. Its shank is made of carbon steel.

File- 

It is a cutting tool and is often used by all artisans. It is used to give the appropriate shape and finishing to a job. They are classified in the following four ways-

According to the length - usually the length of the file is 10, 15, 20, 25, 30, 35 cm.

Grade - Rough, Bastard, Sacred Cut, Smooth, Dad-Smooth etc. occur according to grade.

Cut-cut according to single cut, Dougal cut, Curved cut, Spiral cut and Rasp cut etc. are sandy.

According to the size, flat, round, half round, square, trigular, hand, pipe edge and needle are radial.

Tenon saw — 

It is used to cut wood, sunmica and plastic objects, and to give them the required shape.

Key Hole Saw- 

Sunmica toppers use it to provide the required rectangular or negotiator shape to round holes made by drill machines in wiring boards. It is a short saw with a blade of about 3-4 mm wide and 15–300 cm long.

Hacksaw- 

It is used for cutting sheets of iron and other metals, pipes, wires, nut-bolts etc. It is a metal saw cutting saw. It mainly consists of an adjustable frame, handle, high carbon steel blade and adjustable blade-holder. Its blade has a length sponsorship of 30 cm.

Hand Drill Machine- 

It is used for perforating wood, sunmica, plastic, brass, aluminum, soft iron sheets, spares etc. It is a small manual drill machine. Its capacity is expressed based on its wheel's ability to hold a drill-bit which is usually 6 or 8 mm.

Crimping Tool - 

This is used to crimp the connective 'lug' or 'terminal' at the ends of aluminum cables. Its length is usually 20 cm.

Snips - 

Snips are used to cut thin metallic sheets. It is also used to cut the number of windings, mica sheets, rigid insulation sheets etc., its length is generally